FAQ

Calorific rays were discovered in 1800 by William Herschel when he used a prism to refract sunlight. Using a thermometer, he noticed an increase in temperature beyond the red segment of the visible spectrum. The wavelength of visible light lies in the range between 0.38 (violet) and 0.78 (red) microns, with infrared being ‘just beyond red’ and found between 0.78 – 1000 microns (μm). Over time, these calorific rays became known as ‘infrared’.

In scientific terms, infrared heat is a form, or wave, of electromagnetic radiation. The wavelengths primarily used for the industrial heat process range between 0.78 – 1000 μm.

Infrared is usually divided into 3 sections. The border between the divisions can vary depending on where you read it, as can the designation. At Ceramicx we use the following standard: – Short Wave Infrared: 0.78 – 1.40 μm. Also called Near Infrared [NIR] or IRA – Medium Wave Infrared: 1.4 – 3.0 μm. Also called Mid Infrared [MIR] or IRB – Long Wave Infrared 3 – 1000 μm. Also called Far Infrared [FIR] or IRC.

All objects – including us – above absolute zero (-273.15 °C) naturally radiate infrared energy, so in general terms, the answer would be ‘no’. While infrared can create enough energy to start molecules moving, unlike higher frequency radiation – such as x-rays – it doesn’t have enough energy to break molecules apart or cause damage. Infrared heat will naturally warm up whatever part of you it touches. But lengthy exposure to a high level of IR could be potentially harmful and result in a burn, in the same way as from any other heat source, such as a fire.

Infrared is a form of energy best thought of as waves moving through space that has different frequencies. From low frequencies, which make up radio waves, to high frequencies such as gamma or X-rays, with the visible spectrum of light our eyes can detect (from violet through to red), somewhere in the middle. Infrared (Latin for ‘below red’) is a form of radiation found just below visible light on the electromagnetic spectrum. When we absorb infrared, the only effect is that we feel warmer. However, IR can be hazardous with prolonged exposure. 

Infrared emitters are frequently used under partial vacuum. The direct transfer of radiant energy is generally more efficient due to the absence of water vapour molecules which would normally absorb some of the infrared radiation.

This varies depending on the application, but we generally recommend 100-200mm for static applications where both heater and target are in a fixed position. Optimum distance depends on element spacing and the desired temperature uniformity across the surface. In general, the greater the distance, the greater the radiant dispersion, which in turn facilitates uniform heating. Shorter distances may lead to increased heat energy concentrated over a smaller area which can create localised high-temperature areas.

If the absorption characteristics of the target material are known, it may be possible to use peak emission wavelength as a means of choosing the most suitable emitter. If those characteristics aren’t known, small scale testing with 1 or 2 emitters may be enough to provide a better understanding of what works with the material in question. Another key factor is the thermal response time required by the process. Ceramic emitters typically require about 10-12 minutes to reach steady-state temperature. Quartz cassette emitters require about half this time, with tungsten/halogen emitters close to full output within a few seconds.

Under normal usage, ceramic emitters will last 20,000 hours or 12 months from date of manufacture. For quartz emitters, it’s 10,000 hours or 12 months from date of manufacture.

Our trough-style elements produce a concentrated output which disperses with distance, making it better suited to emitters positioned further from the target. Flat style elements produce a uniform output better suited to emitters positioned closer to the target material.

Again, this varies depending on application and emitter to target distance, but in general, small distances between emitters facilitate improved temperature uniformity. We generally recommend a minimum of 5mm between ceramic emitters when arrayed inside a heater field. We recommend the same with quartz emitters also.

Infrared heat is precise, controllable, and manageable. It’s also more energy-efficient and effective as it targets only the material and the area you want to heat. Conversely, using convectional heat means both the air and the material must be heated, and hot air will always escape, meaning it’s less efficient and more costly.